How to clean your magnetic nasal band correctly

To care for your magnetic nasal band properly, you need to distinguish between the reusable component and the adhesive magnets applied to the skin. Clean the band according to the product instructions, and replace the single-use adhesive magnets after wearing them.

Traces of sweat, skin oils and skincare products can build up on the reusable band. Proper cleaning and storage keep it ready for its next use.

A band with traces of skin oils, sweat or skincare products may no longer sit securely over the magnets. Trying to clean the adhesive part can also affect its hold. A routine that takes just a few minutes keeps the system clean, easy to use and ready for your next night’s sleep or workout.

What to clean and what to replace

In a magnetic system, the nasal band is the flexible piece that sits across the nose and mechanically supports the opening of the outer nasal area when attached to the magnets on either side. This is the reusable component. After wearing it, you can clean it gently before storing it.

The adhesive magnets, on the other hand, come into direct contact with the skin. Their adhesive is designed for one application, rather than washing, vigorous wiping or reuse. Once you remove them, discard them and use a fresh pair next time. A previously worn adhesive magnet can collect skin oils and impurities, and attempting to reapply it will not provide the same comfortable hold.

The rule is easy to remember: clean the band, replace the adhesive magnets.

How to clean your nasal band in 4 simple steps

You do not need special cleaning solutions, alcohol or fragranced products. In fact, harsh products can leave residue or affect the material over time. Choose a gentle, consistent routine.

1. Detach the band before removing the magnets

When you have finished wearing it, first detach the nasal band from the magnets. Do this slowly, without pulling unnecessarily on the material. Then carefully remove the magnets from your skin and discard them.

2. Rinse the band with lukewarm water

Hold the band under a gentle stream of lukewarm water. Follow the water temperature guidance in the product instructions. Rinsing removes light traces of sweat, dust or skin oils that may transfer onto the band during wear.

If you have used a rich cream, sunscreen or makeup around your nose, you may notice a thin film on the band. In this case, water alone may not be enough.

3. Wash gently with mild soap if needed

For visible buildup, use a small amount of mild liquid soap. Gently clean the surface with your fingers, without using a brush, an abrasive sponge or your fingernails. Focus on the surface that touched the skin and any areas with visible residue.

Avoid rubbing alcohol, harsh disinfectant wipes, acetone, perfume and household surface cleaners. They may seem like a quick option, but they can leave a film or change how the material feels. For a band worn close to the skin, gentle cleaning is the practical choice.

4. Rinse thoroughly and leave it to air-dry

Rinse until no traces of soap remain. Then gently shake off the excess water and leave the band to dry completely on a clean towel, away from direct sunlight and heat sources.

Do not dry it on a radiator, use a hairdryer or put it in a washing machine or tumble dryer. Intense heat and washing cycles can distort the band. Also, avoid storing it while damp in a closed container. Air-drying takes little time and helps keep the material in good condition.

How often should you clean it?

Ideally, rinse the band after every use. If you have worn it at night, after a workout or on a warm day, cleaning it straight away is the simplest option. This prevents sweat and skin oils from drying on the surface and leaves the band clean for its next use.

Washing with mild soap is useful when you see buildup or when visible residue remains after rinsing. For some users, this may mean after every wear. For others, occasional washing may be enough, depending on how much they sweat and which products they apply to their face. There is no single frequency that suits everyone—comfort and the appearance of the band are useful guides.

Skin preparation matters just as much

A perfectly clean band cannot compensate for skin around the nose that is covered in oil, cream or sweat. Before applying a fresh pair of adhesive magnets, wash and dry your skin thoroughly. The area must be clean and completely dry.

Avoid creams and oils on the areas where the adhesive magnets attach, as they can reduce adhesion. Lotions and oils can reduce adhesion too. If you exercise, apply the magnets to dry skin before starting, rather than after you have already begun to sweat.

The same principle applies in the evening. A short routine—cleansing your face, drying your skin and applying the magnets—can make the difference between a stable fit and one you feel the need to adjust.

A simple routine for sleep, the gym and travel

If you use the band in the evening, clean it in the morning and leave it to dry while you start your day. If you use it at the gym, rinse it when you get home before storing it. When travelling, a clean case or a separate compartment in your bag helps prevent contact with dusty or damp objects.

In the Refresh Goods system, the PRO Nasal Band is the reusable component, while the adhesive magnets are consumables replaced after wear.

Clean the band according to the product instructions, store it somewhere clean and dry, and prepare your skin before every application.